Even worse, there are multiple causes for this issue, so it can be hard to nail down the exact reason why your computer can't detect your hard drive. Fortunately, there are tricks you can use to better narrow down what's causing this issue.
As such, read on as we cover how to solve an unrecognized hard drive in Windows Depending on whether you are using a PC or laptop, the causes for BIOS not detecting your internal hard drive problem can vary for many reasons. But here are a few of the most common factors to look out for. If you have made changes to your BIOS, including CPU overclocking or memory overclocking, your system may fail to detect your storage drive due to instability.
Fortunately, you can go into the BIOS and revert it to its default configuration to undo any changes. The steps involved to load the default settings can vary depending on your laptop or motherboard manufacturer. Your computer may fail to detect the hard drive if there is a disk failure, drive corruption, and loose connection.
To verify the status of the disk, try removing the hard drive by carefully disconnecting the cables and look for any physical damages. For old hard drives, clean out the dust and connect it to your PC. If the issue persists, try connecting it to a different computer if available. This will help you determine if the issue is with the motherboard or hard drive. The BIOS will not detect a hard drive if the data cable is faulty. Make sure the SATA cables are in good condition, and you have connected them promptly.
Also, inspect the motherboard for bent or misaligned pins. Check your hard drive manufacturer's documentation for the right type of cables. Detailed instructions for installing Serial ATA drives in your computer, including cabling, jumper, and operating system information, and troubleshooting problems that may arise. A Serial ATA interface cable sold separately, unless drive purchased as part of retail kit. Maximum length is 39 inches 1 meter.
A Serial ATA-compatible power cable or adapter sold separately, unless drive purchased as part of retail kit. Handling Precautions Disc drives are fragile. Do not drop or jar the drive. Handle the drive only by the edges or frame. Keep the drive in the protective anti-static container until you are ready to install it to minimize handling damage. Drive electronics are extremely sensitive to static electricity. While installing the drive, wear a wrist strap and cable connected to ground.
Turn off the power to the host system during installation. Do not disassemble the drive. Doing so voids the warranty. Do not apply pressure or attach labels to the circuit board or to the top of the drive.
Attaching Cables and Mounting the Drive Attach one end of the drive interface cable to the Serial ATA interface connector on your computer's motherboard or Serial ATA host adapter see your computer manual for connector locations. Host adapter configuration is shown below. Serial ATA connectors are keyed to ensure correct orientation. Attach the interface and power cables to the drive.
Secure the drive using four UNC mounting screws in either the side-mounting or bottom-mounting holes. Insert the screws no more than 0. Do not overtighten the screws or use metric screws. You can use the free backup software — MiniTool ShadowMaker to do that.
It is a professional backup program that can be used to back up the operating system, disk, partition, file, and folder. Besides, it is a user-friendly program to protect your computer and data. This backup software offers a Trial Edition that allows a day free trial for all backup features.
Free Download. Step 2: After entering the main interface, navigate to the Tools tab. And then choose the Clone Disk feature to continue. Step 3: Next, you are required to choose the source disk and the target disk for cloning. Step 4: After you have successfully selected the disk clone source and destination, click OK to continue. Step 5: Then you will receive a warning message that tells you all data on the target disk will be destroyed during the disk cloning process.
Then click Yes to continue. Step 7: When the disk clone process is finished, you will receive a message which tells you that the source disk and the target disk have the same signature. Thus, you need to remove the ATA from your computer. After reading this post, you know what the ATA hard drive is, how to install ATA hard drive, as well as how to troubleshoot it when it is not working.
If you have any other ideas about the ATA hard drive or any question related to MiniTool software, please leave a comment or contact [email protected] and we will reply to you as soon as possible. Download Shadowmaker. Tip: MiniTool ShadowMaker supports you to clone the dynamic disk, but it is just for the simple volume.
Note: If there are important data on the target SATA hard drive, you had better back up them in advance. Maybe this post - How to Backup Files on Windows 10? Try These Top 4 Ways is what you need. Power on the system.
0コメント